Email your questions to:
PZGunsmith@KIH.Net
PZGunsmith@KIH.Net
 | |  | |  | |  | |  | |  | |  |
|
Ky Guns
|
25 Round
Magazine
Magazine
We all have seen the high capacity magazines for the Ruger 10/22 Rifle. And for
the most part, there is not much difference from one to the other. Sometimes they
work, and sometimes they don't. Maybe you have had to hold the magazine
pushed forward with you thumb in order to get it to feed, or maybe you had to
push it in as you shoot, especially if you have two mags attached side by side. Or
maybe they just don't work in one rifle or the other. Now these problems are in
the past.
The Tactical Innovations Magazine is the one and only high capacity magazine
that fits and feeds in all rifles. And not only that, it is practically indestructible.
Here's how.
The TI Magazine is built with a steel upper that includes feed lips, and the front
and rear attachment pins. It also incorporates four adjustment screws at the top
of the magazine to allow for fitting to individual rifles. Since all rifles vary in the
depth of the magazine well, unless the magazine fits properly it is likely to jamb.
By making a small adjustment to these screws a near perfect fit can be achieved
in order to make sure your magazine will feed in your rifle.
Having a polymer (Black) or Aluminium Body, these magazines have been
designed to last a lifetime. Now add the fact that each one can be disassembled
using the supplied allen wrench to remove three screws and the problem of
jambing due to a dirty magazine has been eliminated.
I believe that this is one of the best investments you can make to improve your
shooting pleasure with the Ruger 10/22. Take your pick, Black Polymer or
Machined Aluminum. The aluminum is a little expensive but it sure does go well
with the Stainless Ruger.
the most part, there is not much difference from one to the other. Sometimes they
work, and sometimes they don't. Maybe you have had to hold the magazine
pushed forward with you thumb in order to get it to feed, or maybe you had to
push it in as you shoot, especially if you have two mags attached side by side. Or
maybe they just don't work in one rifle or the other. Now these problems are in
the past.
The Tactical Innovations Magazine is the one and only high capacity magazine
that fits and feeds in all rifles. And not only that, it is practically indestructible.
Here's how.
The TI Magazine is built with a steel upper that includes feed lips, and the front
and rear attachment pins. It also incorporates four adjustment screws at the top
of the magazine to allow for fitting to individual rifles. Since all rifles vary in the
depth of the magazine well, unless the magazine fits properly it is likely to jamb.
By making a small adjustment to these screws a near perfect fit can be achieved
in order to make sure your magazine will feed in your rifle.
Having a polymer (Black) or Aluminium Body, these magazines have been
designed to last a lifetime. Now add the fact that each one can be disassembled
using the supplied allen wrench to remove three screws and the problem of
jambing due to a dirty magazine has been eliminated.
I believe that this is one of the best investments you can make to improve your
shooting pleasure with the Ruger 10/22. Take your pick, Black Polymer or
Machined Aluminum. The aluminum is a little expensive but it sure does go well
with the Stainless Ruger.
| Tactical Solutions Compensators |
Designed to fit the Tactical Solutions Barrels with threaded ends, these
compensators make for a stunning addition to the Rifle or Pistol Barrel. The
compensator matches the barrel diameter to make for a seamless addition to the
barrel. Choose either a matching color or a contrast such as a Matte Black
Compensator on a Matte Green Barrel. These are also available for the Gloss
Black, Silver, and colored barrels.
compensators make for a stunning addition to the Rifle or Pistol Barrel. The
compensator matches the barrel diameter to make for a seamless addition to the
barrel. Choose either a matching color or a contrast such as a Matte Black
Compensator on a Matte Green Barrel. These are also available for the Gloss
Black, Silver, and colored barrels.
| My Price -- $37.99 ea Call for Available Color Specify For Rifle or Pistol |
| Tactical Solutions Scope Bases |
| Scope Base Rifle |
Compensators
| Scope Rings |
| Scope Base for a Browning Buckmark Pistol |
The Tactical Solutions Scope Base is a Picatinny style base. It will fit any Weaver
type rings, but goes exceptionally with the Tactical Solutions Quick Detachable
Rings. The base is precision cut to fit the 10/22 Rifle and to give precise fitting of
the rings to the base. With a large number of slots in the base, it is easy to get the
alignment of your scope where you want it.
type rings, but goes exceptionally with the Tactical Solutions Quick Detachable
Rings. The base is precision cut to fit the 10/22 Rifle and to give precise fitting of
the rings to the base. With a large number of slots in the base, it is easy to get the
alignment of your scope where you want it.
This is also a Picatinny style scope base byTactical Solutions Scope Base. Just like
the rifle base, it will fit any Weaver type rings, but goes exceptionally with the
Tactical Solutions Quick Detachable Rings. This base comes with or without the
rear sight and is easily installed by removing the two screws on the Browning Top
Strap and replacing it with this base.
the rifle base, it will fit any Weaver type rings, but goes exceptionally with the
Tactical Solutions Quick Detachable Rings. This base comes with or without the
rear sight and is easily installed by removing the two screws on the Browning Top
Strap and replacing it with this base.
| Tactical Solutions Quick Detachable Scope Rings |
| Scope Base Pistol |
Retail Price -- $35.00
Our Price -- $29.99
Our Price -- $29.99
Retail Price -- $33.00
Our Price -- $29.99
Our Price -- $29.99
Retail Price -- $85.00
Our Price -- $69.99
Our Price -- $69.99
Quick Detachable Rings -- $37.50
Without a doubt, these are some of the finest rings to be had. They may
be quickly detached and re-attached to the base without loosing zero.
You have to see the quality built into these rings to appreciate them.
Available in 1" or 30 mm, please specify when calling.
be quickly detached and re-attached to the base without loosing zero.
You have to see the quality built into these rings to appreciate them.
Available in 1" or 30 mm, please specify when calling.
| Tru Glo Red Dot Sight |
| Tru Glo Red Dot Sight for Rifle or Pistol |
Whether shooting a Rifle or a Pistol, the hardest thing to do is to align your sights, not
to the target, but to one another. Sight alignment is the most critical part of shooting
as a little mistake here means a big mistake down range. Competitive Pistol shooters
want the longest barrel practical to make these small errors less critical.
Scopes on the other hand eliminate the alignment problem and give a magnification
that brings the target in closer thus it is easier to see. But aligning a scope on a pistol
so that you can see through it can be a problem.
So what is the solution? Answer: A Red Dot Sight. The Red Dot allows you to look at
your target without aligning sights as does a scope, but it is easier to see through and
align on target. Just place the Red Dot on the target where you want the bullet to
impact and squeeze the trigger. The dot is not actually on the target such as with a
lazer, but appears to be there to your eyes.
The quick acquisition of a target and the accuracy you can achieve of a Red Dot was
recognized by the military and adopted for use with the M-4 Service Rifle. I have
personally used the Red Dot many times and have been successful hunting with it on
my pistols. Once you try one you will be amazed at how easy they are to use.
The Tru Glo sight is a high quality Red Dot Sight that will give years of satisfaction. It
is fully adjustable for windage and elevation, fits a Weaver type base, and it allows
you to change the battery without removing the sight from the firearm. This is
especially nice as it does not require sighting in again. I like them and I use them, and
I know you will be pleased with them too.
to the target, but to one another. Sight alignment is the most critical part of shooting
as a little mistake here means a big mistake down range. Competitive Pistol shooters
want the longest barrel practical to make these small errors less critical.
Scopes on the other hand eliminate the alignment problem and give a magnification
that brings the target in closer thus it is easier to see. But aligning a scope on a pistol
so that you can see through it can be a problem.
So what is the solution? Answer: A Red Dot Sight. The Red Dot allows you to look at
your target without aligning sights as does a scope, but it is easier to see through and
align on target. Just place the Red Dot on the target where you want the bullet to
impact and squeeze the trigger. The dot is not actually on the target such as with a
lazer, but appears to be there to your eyes.
The quick acquisition of a target and the accuracy you can achieve of a Red Dot was
recognized by the military and adopted for use with the M-4 Service Rifle. I have
personally used the Red Dot many times and have been successful hunting with it on
my pistols. Once you try one you will be amazed at how easy they are to use.
The Tru Glo sight is a high quality Red Dot Sight that will give years of satisfaction. It
is fully adjustable for windage and elevation, fits a Weaver type base, and it allows
you to change the battery without removing the sight from the firearm. This is
especially nice as it does not require sighting in again. I like them and I use them, and
I know you will be pleased with them too.
Tru Glo Red Dot Sight -- $234.99
| Rifle and Pistol Accessories |
Simply the best that money can buy!!!!
Polymer Mags $44.99 ea
Poly Carb Mags $24.99 ea
Poly Carb Mags $24.99 ea
| Fiber Front Sights for Pac Lite Pistols |
The fiber front sight has been around for many years and makes the sight easier to see.
Made for the Tactical Solutions Pac Lite Pistol, these come in Red, Orange, or Green.
The Pac Lite has two different barrel diameters, the Standard Barrel is smaller in
diameter than the Receiver, and the Bull Barrel is the same diameter. Use the Tall Sight
for the Small Barrel and the Short Sight for the Bull Barrel. One screw holds the sight in
place and is easy for the average shooter to install.
Made for the Tactical Solutions Pac Lite Pistol, these come in Red, Orange, or Green.
The Pac Lite has two different barrel diameters, the Standard Barrel is smaller in
diameter than the Receiver, and the Bull Barrel is the same diameter. Use the Tall Sight
for the Small Barrel and the Short Sight for the Bull Barrel. One screw holds the sight in
place and is easy for the average shooter to install.
Fiber Front Sight -- $17.99 each
The Trigger Guard 2000 is a complete CNC machined trigger guard equipped with
precision EDM parts. It features an internal pretravel adjustment that is set at the factory in
order to greatly reduce pretravel usually found on the factory trigger guard.
This new match trigger guard is CNC machined from a solid billet of high strength aircraft
aluminum.
The hammer, sear and disconnector are precision wire EDM cut from A2 hardened tool
steel with tolerances being held to +/- .0002" assuring every trigger let off to be extremely
consistent.
The CNC machined trigger is hard black anodized and equipped with an overtravel
adjustment screw. The trigger is reset internally to eliminate any dragging or
inconsistencies caused by a conventional trigger plunger.
The TG2000 comes with custom springs, an automatic bolt release, and an extended
magazine release.
This new competition trigger guard is machined to give a superb, crisp trigger that will
provide years of enjoyment to the shooter who demands the very best.
precision EDM parts. It features an internal pretravel adjustment that is set at the factory in
order to greatly reduce pretravel usually found on the factory trigger guard.
This new match trigger guard is CNC machined from a solid billet of high strength aircraft
aluminum.
The hammer, sear and disconnector are precision wire EDM cut from A2 hardened tool
steel with tolerances being held to +/- .0002" assuring every trigger let off to be extremely
consistent.
The CNC machined trigger is hard black anodized and equipped with an overtravel
adjustment screw. The trigger is reset internally to eliminate any dragging or
inconsistencies caused by a conventional trigger plunger.
The TG2000 comes with custom springs, an automatic bolt release, and an extended
magazine release.
This new competition trigger guard is machined to give a superb, crisp trigger that will
provide years of enjoyment to the shooter who demands the very best.
| Custom Target Triggers |
| Volquartsen TG 2000 Target Triggers |
TG 2000 Black Trigger Assembly -- $209.99
TG 2000 Silver Grigger Assembly -- $209.99
Red, Orange, or Green
 | |  | |  |
Pistol Base
Rifle Base
Buckmark Base With Sight
This is another Picatinny style base, but for the Pac Lite Pistol. It will fit any Weaver type
rings and goes exceptionally well with the Tactical Solutions Quick Detachable Rings. I
use this on my pistols to mount the Tru Glow Red Dot Sight listed below. Sure makes
shooting a pistol easier and I hit what I'm shooting at a lot more too.
rings and goes exceptionally well with the Tactical Solutions Quick Detachable Rings. I
use this on my pistols to mount the Tru Glow Red Dot Sight listed below. Sure makes
shooting a pistol easier and I hit what I'm shooting at a lot more too.
Composite
Polycarb
Aluminium